THE THAI KITCHEN EXPLORER

Clay and ceramic terminology

A plain guide to clay and ceramic terms: earthenware, stoneware and porcelain, plus plasticity, shrinkage, grog, slip and wedging explained for beginners.

8 min read0 viewsClay and ceramic terminology
— · 0 votes
Contents
  1. What clay and ceramic terms describe
  2. Earthenware, stoneware and porcelain
  3. Plasticity and workability of clay
  4. Shrinkage from wet clay to fired piece
  5. Grog, sand and other fillers
  6. Slip, slurry and joining clay
  7. Wedging and preparing the clay
  8. Glaze and firing words that follow clay
  9. Questions about clay and ceramic terms
  10. What is the difference between clay and ceramic?
  11. What does plasticity mean in pottery clay?
  12. Why does clay shrink when it dries and fires?
  13. What is grog used for in a clay body?
  14. How is slip different from glaze?
  15. What does wedging clay do?

Clay and ceramic terminology is the vocabulary potters use to name the raw material, its behavior and the stages it passes through. Knowing these clay terms makes a glaze recipe, a kiln schedule or a supplier's label easier to read. The words below cover the pottery clay terms you meet first when you start working with clay.

  • Earthenware, stoneware and porcelain are clay bodies with different firing ranges and porosity.
  • Plasticity describes how easily a clay body bends and holds a shape without cracking.
  • Shrinkage is the loss of size as water leaves the clay and as the fired piece cools.
  • Grog is fired clay ground and added to a body to reduce shrinkage and open the texture.
  • Slip is clay mixed with water, used as a glue, a coating or a casting liquid.

What clay and ceramic terms describe

Clay is a fine-grained natural material that becomes plastic when wet and hard when fired. Ceramic is the wider word for objects made from clay and hardened by heat, so a ceramic piece can be earthenware, stoneware or porcelain. The vocabulary of the craft separates the raw material from the finished object and from the process in between.

A clay body is a prepared blend of clays and other minerals rather than a single dug-up lump. Potters buy or mix a body to suit a method such as throwing on a wheel, hand building or casting in a mold. The name of a body tells you its firing range and its fired character more reliably than the color of the wet clay.

Firing is the heating of clay in a kiln until the material changes permanently. The temperature a body is fired to shapes its porosity, strength and color. Terms about firing matter because the same clay behaves differently at different temperatures.

Earthenware, stoneware and porcelain

Earthenware clay fires at a lower temperature than the other two main bodies and stays porous after firing. An earthenware pot absorbs water unless it is glazed, and its body stays softer and warmer in color. Terracotta is an earthenware clay rich in iron, which gives it a red-orange tone.

Stoneware clay fires hot enough that the body becomes dense and vitrified, meaning it absorbs little water. Stoneware suits everyday dishes and cooking vessels because the fired body is strong and resistant to liquid. The higher temperature also limits which glazes and colors behave well on it.

Porcelain is a white, finely textured clay body fired to a high temperature until it turns glassy and translucent where thin. Porcelain demands more care in forming because the body is less forgiving and can slump in the kiln. Each of these three bodies needs a matching firing range, so a glaze made for one is not automatically right for another.

BodyFired characterWater absorption
EarthenwareSofter, warm color, porousAbsorbs water if unglazed
StonewareDense, strong, muted colorLow absorption
PorcelainWhite, glassy, translucent when thinVery low absorption

Plasticity and workability of clay

Plasticity is the ability of a wet clay body to bend, stretch and hold a shape without tearing. A plastic body throws well on the wheel and coils without cracking at the joins. Clay with too little plasticity crumbles at the edges and resists shaping.

Workability covers plasticity plus how the body feels in the hand, how it releases from a mold and how it dries. A body can be plastic yet sticky, or plastic yet short and prone to splitting. Potters adjust workability by blending clays, aging the wet body or adding a fine filler.

Water content sits at the center of workability, because clay must be damp enough to move and dry enough to stand. Leather-hard describes clay that has stiffened but still holds moisture, a stage used for trimming and joining. Bone-dry clay has lost nearly all its water and is ready for the first firing.

Shrinkage from wet clay to fired piece

Shrinkage is the reduction in size a clay piece undergoes as water leaves it and as it is fired. A pot measured wet will be smaller when leather-hard, smaller again when bone-dry and smaller still after firing. Potters account for shrinkage when they make a lid, a set of matching pieces or a form that must fit something else.

Drying shrinkage happens as water leaves the spaces between clay particles and they pack closer together. Firing shrinkage happens as the body densifies and any remaining organic matter burns away. A body with a lot of fine clay shrinks more than a body loaded with coarse filler.

Uneven shrinkage causes warping, cracking and pulled joins, especially when one part of a piece dries faster than another. Slow, even drying under a cover reduces the strain on a pot. Joining two pieces of different moisture content invites a crack at the seam.

Grog, sand and other fillers

Grog is fired clay that has been crushed and added to a clay body to open its texture and reduce shrinkage. The grog particles are already shrunk, so they take up space that fine clay would otherwise fill. A groggy body holds its shape well in hand building and tolerates thermal shock in the kiln.

Sand, chamotte and crushed shell serve a similar purpose as non-plastic fillers in a body. These additions make clay less sticky and easier to dry without warping. They also make the fired surface rougher, which matters when a smooth finish is wanted.

Coarse grog suits large sculptural forms and ovenware, where resistance to cracking matters more than a fine surface. Fine grog gives a smoother texture while still easing shrinkage. Adding grog to a body weakens its plasticity, so the amount has to match the forming method.

Slip, slurry and joining clay

Slip is clay suspended in water, used to join two pieces, coat a surface or fill a mold. A thick slip acts as a glue when scored into both surfaces of a join. A thin slip can be poured into a plaster mold to cast a hollow form as the plaster draws water out.

Slurry is the runnier mixture of clay and water that collects during work or is made for casting. Slip and slurry differ mainly in how much water they carry and what job they do. Decorating slip, called engobe, is colored with oxides or stains and applied to a damp or leather-hard surface.

A join made with slip needs both surfaces scored and pressed together while still damp. Slip that has dried out on the shelf may need water and mixing before it bonds again. Mixing slip from the same body as the pieces keeps shrinkage matched at the seam.

Wedging and preparing the clay

Wedging is the kneading of clay to remove air pockets and make its moisture even throughout. Air trapped in a body can blow a piece apart in the kiln as it expands. Uneven moisture causes one part of a pot to shrink differently from the rest.

Spiral wedging and cut-and-slam wedging are two hand methods for working a lump of clay. A mechanical pug mill does the same job by forcing clay through a vacuum chamber. Whichever method is used, the aim is a consistent body with no hidden voids.

Clay straight from a bag or a stored block benefits from wedging before it goes on the wheel. Freshly wedged clay also needs a rest so the moisture can spread evenly. Skipping the rest can leave a body that feels stiff in one area and soft in another.

Glaze and firing words that follow clay

Glaze is a glassy coating melted onto a fired or unfired clay surface, and it makes a porous body hold liquid. The glaze and the clay body must fit each other, because a glaze that shrinks differently can craze or peel. A crazed glaze shows a network of fine cracks, while a shivering glaze flakes away from the body.

Bisque firing is the first firing, which hardens the clay enough to handle and glaze without melting it. The glaze firing comes after glazing and brings the coating to its melted state. Some potters combine the two in a single firing, which demands a body and glaze matched for the same schedule.

Vitrification is the point at which a fired body becomes dense and glassy enough to resist water. Overfiring pushes a body past that point and can cause slumping or bloating. A kiln schedule is the plan of temperatures and holds that carries a piece through these changes.

Questions about clay and ceramic terms

What is the difference between clay and ceramic?

Clay is the raw earthy material, and ceramic is the finished object made from it and hardened by heat. All ceramic ware starts as clay, but the word ceramic also covers the glaze and the firing that turn a soft lump into a hard pot.

What does plasticity mean in pottery clay?

Plasticity is how well a wet clay body bends and holds a shape without tearing or cracking. A plastic body throws and coils easily, while a short body crumbles at the edges and resists shaping.

Why does clay shrink when it dries and fires?

Clay shrinks as water leaves the spaces between particles and again as the body densifies in the kiln. A body rich in fine clay shrinks more than one with a lot of grog or sand filler, so the amount depends on the blend.

What is grog used for in a clay body?

Grog is crushed fired clay added to a body to open its texture and cut down shrinkage. It also helps a piece resist cracking during drying and firing, at the cost of a rougher surface.

How is slip different from glaze?

Slip is clay mixed with water and used to join, coat or cast a piece before firing. Glaze is a glassy coating that melts in the kiln, so slip changes the clay surface while glaze seals and colors it.

What does wedging clay do?

Wedging removes trapped air and evens out moisture through a lump of clay. A well wedged body forms more predictably and is less likely to crack or blow apart in the kiln.

Read next

Latest articles