Board foot calculator for lumber and hardwood
Learn how a board foot calculator works for lumber and hardwood, the board foot formula, and how to measure rough boards and nominal sizes by hand.
Contents
- What a board foot measures
- The board foot formula in plain words
- Measuring rough lumber correctly
- Nominal versus actual dimensions
- Running the numbers on several boards
- Wood web calculator results and rounding
- Where a calculator helps and where it does not
- Board foot questions for lumber buyers
- How do I use a hardwood board foot calculator?
- What is the board foot formula for rough lumber?
- Does a lumber board foot calculator work for any wood?
- Why do nominal and actual sizes give different board feet?
- How many board feet are in one board?
- Can a wood board foot calculator replace measuring the wood?
A board foot calculator turns three measurements of a board into a volume figure called board feet. One board foot is a volume of wood equal to 12 inches by 12 inches by 1 inch, and the calculator applies that standard to any piece. You can also do the same math on paper with the board foot formula.
- One board foot equals 144 cubic inches of wood, the unit buyers use to price lumber.
- Multiply thickness by width by length in inches, then divide by 12 to get board feet.
- Use the rough thickness and width of unfinished hardwood, not the final planed size.
- Measure the length in inches first when you use the formula, then convert feet if needed.
- A calculator only helps if your measurements match the way the seller measures the board.
What a board foot measures
A board foot measures the volume of lumber, not its surface area or its weight. The unit describes how much wood a board contains, which is why lumber sellers price hardwood by the board foot rather than by the piece. Thickness, width and length all feed into the number.
The reference size is a piece 12 inches wide, 12 inches long and 1 inch thick. That block holds 144 cubic inches of wood, and the board foot is defined from it. A board twice as thick holds twice the board feet at the same surface size.
Softwood framing lumber is often sold by nominal size and length instead. Hardwood boards, rough lumber and turning blanks move through the trade as measured volume. Knowing which system a seller uses tells you what the calculator result should be compared against.
The board foot formula in plain words
The board foot formula is thickness times width times length divided by 12. Nominal thickness and width go in as inches, and the length goes in as inches until the final step. Dividing by 12 converts the result into board feet.
A board 1 inch thick, 6 inches wide and 24 inches long gives 144 when you multiply the three figures. Dividing 144 by 12 yields 12 board feet for that piece. The same steps apply to any rectangular board you can measure.
Some people work the length in feet and divide by 12 at a different point. Both routes give the same answer when the units stay consistent. Write the units beside each number so a mixed measurement does not slip through.
Measuring rough lumber correctly
Rough lumber is measured at its rough thickness and width, before planing removes any surface. A board sold as one inch rough may plane down thinner, but the board foot count comes from the rough figure. Measuring the finished face understates the volume you pay for.
Take the width at the narrowest sound point of the board when the edges are not parallel. Hardwood boards often taper, and the seller measures the usable width rather than the widest spot. Record the length along the full board from end to end.
Check for defects that change the usable area before you settle on a width. A split end or a large knot may reduce what the board yields, though the board foot count still reflects the measured size. Ask the seller which measurement basis applies to the stack.
Nominal versus actual dimensions
Nominal versus actual lumber dimensions is the gap between the name of a board and its measured size. A board called one inch by six inches may measure closer to three quarters of an inch by five and a half inches. The board foot count for hardwood rough stock normally uses the nominal rough size.
Planed lumber sold to a finished size creates confusion when you compare it with the formula. Measure the board in front of you and decide whether the price refers to rough or dressed stock. The two figures can differ enough to change the total cost of a project.
Keeping a small note of each board's nominal and actual size prevents mix-ups at the counter. The board foot calculator handles the arithmetic, but you supply the size that matches the seller's basis. Consistency between the two is what keeps the estimate honest.
Running the numbers on several boards
Board feet per piece add up into a total for a stack, and you repeat the formula for each board first. Boards of the same size can be grouped by multiplying one result by the count. Mixed sizes need a separate line each until the total is complete.
A simple tally sheet with columns for thickness, width, length and board feet keeps the work clear. Round each piece to a sensible fraction before you multiply to avoid drifting totals. Add the pieces at the end rather than trusting a running figure in your head.
A calculator app or a spreadsheet formula does the same job faster on a large order. Enter measurements in the same units throughout and read the total against the seller's figure. A small difference is normal when rounding rules differ.
| Piece | Thickness (in) | Width (in) | Length (in) | Board feet |
|---|---|---|---|---|
| A | 1 | 6 | 24 | 12 |
| B | 2 | 4 | 36 | 24 |
| C | 1 | 8 | 12 | 8 |
Wood web calculator results and rounding
A wood web calculator is one of several online tools that apply the same board foot formula. Results from any calculator depend on the figures you type in, not on the tool. Compare two results only when the inputs match exactly.
Rounding rules change totals on many small pieces. The formula gives a decimal figure, and sellers may round up per board or round the final total. Ask which rule the seller applies so your count and the invoice agree.
Fractions are the other source of drift. Measure in sixteenths or quarters and convert to a decimal with care. A calculator accepts decimals cleanly, while a hand tally may need the fraction kept in view.
Where a calculator helps and where it does not
A hardwood board foot calculator speeds up an order with many pieces and reduces arithmetic slips. The tool cannot tell you whether a board is sound, straight or free of defects. Those judgments stay with your eyes and hands on the wood.
Volume from the formula is not the same as yield in a finished project. Sawing, planing and waste remove material, so the board feet you buy exceed the wood in the final part. Plan for that difference when you order stock.
Heavy boards and stacked lumber need safe handling, and a large order may call for help from the yard staff. Use the calculator for the count and leave lifting and machine work to people trained for it. No figure from a tool replaces care at the saw.
Board foot questions for lumber buyers
How do I use a hardwood board foot calculator?
Enter the thickness, width and length of each board in inches, and the tool divides the product by 12. Group boards of the same size to save time, then add the groups. Keep the rough or nominal size consistent with the seller's basis.
What is the board foot formula for rough lumber?
The board foot formula for rough lumber is thickness times width times length divided by 12. Use the rough thickness and the usable width, measured at the narrowest sound point. The result is the volume of that piece in board feet.
Does a lumber board foot calculator work for any wood?
A lumber board foot calculator works for any board measured by volume, whatever the species. The math uses dimensions alone and does not change with the type of wood. Check only that the seller prices by board feet for that stock.
Why do nominal and actual sizes give different board feet?
Nominal and actual sizes differ because planing removes material after the board is cut. A board called one inch thick may measure three quarters of an inch when dressed. Hardwood sold as rough stock is counted at the rough size, which is the larger figure.
How many board feet are in one board?
One board holds as many board feet as its volume allows, with 144 cubic inches in each board foot. Multiply thickness, width and length in inches, then divide by 12. A one inch by twelve inch by twelve inch board gives exactly one board foot.
Can a wood board foot calculator replace measuring the wood?
No, a wood board foot calculator needs your measurements and cannot inspect the wood itself. Measure each board and note defects that affect the usable area. The tool does the arithmetic, while you judge the stock.