# Troubleshooting Pottery: Common Problems and Fixes

Diagnose clay pot problems from wet clay to the kiln, from cracking and black core to bloating and glaze faults, with clear fixes for each stage.

Pottery troubleshooting starts with finding which stage caused the fault, because wet work, drying and firing each leave their own marks. Cracking, black core, bloating and glaze faults almost always trace back to one specific step. Read the fault, match it to its cause, and fix that step rather than the finished pot. 

- Match the fault to its stage: shaping, drying, bisque firing, glazing or glaze firing.
- Slow, even drying prevents far more cracks than any repair after the fact.
- Black core comes from carbon trapped by firing too fast early in the kiln cycle.
- Bloating means the clay body was overfired or still carried too much moisture.
- Write a short record of every firing so a fault can be traced to a known cause.
 

## Start with the stage, not the pot 

Pottery troubleshooting works like a short checklist that moves through the stages of making. A fault visible on a finished clay pot was caused earlier, sometimes weeks before the pot came out of the kiln. The mark itself tells you where to look first. 

Cracks with soft, rounded edges formed while the clay was wet or drying. Sharp cracks and shivering appeared during firing or cooling. A dark core inside a broken shard points to the bisque firing, not the glaze. 

Keep a simple log for each batch: clay body, thickness, drying time and kiln cycle. When a fault appears, the log narrows the cause instead of guessing. This habit carries intermediate pottery skills further than any single repair trick. 

## Cracking during shaping and drying 

Cracking is the clay pot problem that begins long before the kiln, and it comes from uneven shrinkage. Clay shrinks as water leaves it, and any part that dries faster than its neighbor pulls away and tears. 

Attach handles, spouts and feet to leather-hard clay of the same moisture, and score and slip the joint well. Wrap the joined pot in plastic for a day so the parts equalize before open drying. Uneven wall thickness is a frequent root of later cracks. 

Dry kitchenware pottery slowly and evenly, with the rim covered so it does not stiffen first. Turn thin pots over once they hold their shape, and keep them away from drafts and direct sun. 

- Score and slip every joint, then wrap the piece in plastic to equalize moisture
- Press a coil of the same clay into the joint for added strength
- Keep wall thickness even across the base and sides
- Cover rims with plastic so they dry last, not first
- Dry in a cool, draft-free spot and turn thin pieces once they hold shape
 

## Black core and carbon trapping 

Black core is a dark, gray or black zone in the middle of a clay wall, and it forms when carbon cannot burn out. Organic matter in the clay needs oxygen and time to leave the body, and a fast early firing seals the surface first. 

The fix sits in the bisque firing. Fire slowly through the early part of the cycle, keep the kiln vented, and hold the temperature once the clay is red hot so oxygen reaches the carbon. Thick walls need more time than thin ones. 

A black core weakens the pot and can bloat later in a glaze firing. Break a test shard to check the color of the body before you trust a new clay or a new firing schedule. 

## Bloating, warping and overfiring 

Bloating shows as a swollen blister on the clay surface, and it means gas expanded inside a body that had already sealed. The cause is either firing clay above its maturity or firing a pot that still held moisture. 

Warping follows the same logic: a body fired past its maturing point softens and slumps under its own weight. Flat bases, wide plates and tall handles show it first. Kitchenware clay bodies need a firing range that suits their use. 

Confirm the maturing range for each clay body and fire within it. Make sure pots are bone dry before the kiln, and slow the climb through the last part of the firing to let the body stiffen evenly. 
| Symptom | Likely cause | Fix | 
| Bloating | Overfiring or trapped moisture | Fire within the clay's range and dry pots fully | 
| Warping | Body too soft at top temperature | Reduce the top temperature and support flat forms | 
| Black core | Carbon trapped by a fast early firing | Fire slowly and vent the kiln early | 
| Cracking | Uneven drying or thickness | Equalize moisture and even out walls |  

## Crazing and glaze faults 

Crazing is a network of fine cracks in a glaze, and it happens when the glaze contracts more than the clay body beneath it. The glaze is under tension, so it splits to relieve the stress. A glaze that fits the body will not craze. 

Shivering is the opposite fault, where the glaze lifts off the rim in flakes. Crazing and shivering both point to a mismatch between glaze and clay, and the fix is to adjust the glaze rather than the pot. 

Other glaze faults come from application: crawling where the glaze pulls away from dusty clay, pinholing where gas escapes through the melt, and running where too much glaze was applied. Clean the bisque, apply even coats, and test each glaze on the intended clay body. 

## Kiln problems and firing records 

Kiln problems show up as faults across a whole load rather than on one pot. A cold spot, a stuck element or a door that does not seal will leave a pattern, so check where the faulty pots sat in the kiln. 

Place pots so heat can move freely, and keep glazed pieces from touching shelves or each other. A shelf that has been contaminated with glaze can leave marks on the base of the next pot. 

Record the kiln cycle, the load position and the result for every firing. A pottery troubleshooting checklist built from those records turns a mystery into a known cause within a few batches. 

## Thai kitchenware: faults that matter for use 

Kitchenware pottery carries extra risk, because a fault can affect food contact and heat resistance. A crack, a crazed glaze or a black core on a mortar or cooking pot is a reason to keep that piece out of the kitchen. 

[Thai kitchen tools](/articles/thai-cooking-tools-equipment-preparation-material-44546/) such as clay mortars and cooking pots need clay bodies and glazes chosen for heat and for food. Thermal shock from a sudden temperature change can crack a pot that was sound in the kiln, so warm and cool these pieces gradually. 

Treat any pot that holds water, takes direct heat or touches food with extra care when a fault appears. If you are unsure whether a piece is sound, ask a trained potter to assess it before use. 

## Pottery Troubleshooting Questions 

### Why did my clay pot crack while it was drying? 

Cracking during drying comes from uneven shrinkage, with one part of the pot losing water faster than another. Thick bases with thin walls, rushed joins and drafts all speed the difference. Dry pieces slowly and evenly, and equalize moisture at every joint. 

### What causes a black core in fired clay? 

A black core forms when carbon in the clay body cannot burn out before the surface seals. The usual cause is firing too fast through the early part of the bisque cycle without enough oxygen. Fire slowly at the start, vent the kiln, and hold the temperature so the carbon can leave. 

### Why is my glaze crazing on kitchenware pottery? 

Crazing means the glaze is contracting more than the clay body, so it splits into fine cracks. The glaze and the body do not fit each other well enough. Adjust the glaze or change the clay body, and remember that a crazed glaze on a food pot is a reason to stop using it. 

### What are the clay pot firing problems to watch for? 

The main firing problems are bloating, warping, black core, cracking and glaze faults such as pinholing and crawling. Each one traces back to the clay body, the moisture level, the firing schedule or the glaze fit. A written record of each firing helps you trace the cause quickly. 

### Can I fix a cracked pot after firing? 

A fired clay pot cannot be repaired in a way that restores its strength for food or heat use. Adhesive may hold a decorative piece together, but it does not make a kitchen pot sound again. Keep fired pieces with cracks or crazing out of cooking and food contact. 

### Why does my pot warp in the kiln? 

Warping happens when the clay body softens at the top of the firing and cannot hold its shape. Overfiring, uneven wall thickness and heavy flat forms all make it worse. Fire within the clay's maturing range, support flat pieces, and slow the final climb.
