# Regrinding a Chipped Cleaver Edge

Learn how to regrind a chipped cleaver edge, set the cleaver bevel, remove chips on a thick blade and finish with burr removal on a sharpening stone.

Regrinding a chipped cleaver edge means grinding the whole bevel back until the chipped section is gone and a fresh edge meets the bevel. A cleaver has a thick, heavy blade, so the work takes a coarse grit, patience and a steady bevel angle. The goal is a straight, even edge that slices cleanly again, not a quick patch over the chip. 

- Grind the full bevel back until the chip disappears, rather than touching up only the damaged spot.
- Start with a coarse grit and hold one consistent bevel angle along the whole edge.
- A thick cleaver blade removes metal slowly, so check your progress often.
- Raise a burr along the full edge before you move to finer stones.
- Remove the burr at the end so the edge is clean and stable.
 

## What regrinding a cleaver edge involves 

Regrinding a cleaver edge is edge reprofiling on a heavy blade, not a light touch-up. The chipped cleaver edge has lost metal at one point, so the surrounding bevel must come down to meet the lowest point of the damage. Grinding a small spot alone leaves a dip that catches food and weakens the edge. 

The cleaver bevel is the angled face that runs from the edge up to the flat of the blade. Regrinding cleaver bevel work means restoring that face at a steady angle on both sides where the blade is ground on both. A meat cleaver often has a thick blade, so the bevel is wide and the metal behind the edge is substantial. 

Chip removal on a thick blade is mostly about time and control. The steel is sturdy, so the stone cuts slowly and the angle is easy to drift. Check the edge against a light after each round of grinding to see where metal is still missing. 

## Check the chip before you grind 

Inspect the chipped cleaver edge under good light before any grinding starts. Look along the edge from the side and note the depth of the chip and how much of the edge it affects. A shallow nick needs less metal removed than a deep fracture. 

Run a finger along the flat of the blade, not the edge, to feel for bends or cracks near the chip. A bent section will not grind away cleanly, so straighten it first or have a trained specialist look at it. Cracks that run into the blade body are a reason to stop and seek professional help. 

Mark the chipped area with a marker or a small dab of paint so you can watch it shrink as you grind. The mark shows when the chip is gone and prevents overgrinding. Remove the mark when the edge is even. 

## Choose the grit and the tool 

A coarse grit does the heavy work of regrinding a chipped cleaver edge. A coarse sharpening stone or a coarse grinding wheel removes metal faster than a fine stone. The right grit depends on the chip depth and the steel hardness of the blade. 

A grinding wheel runs fast and needs a light touch to avoid overheating the thin edge. A sharpening stone gives more control and is easier to keep flat. Many cooks use a coarse stone for the repair and finer stones for the finish. 

Wet the stone or keep the wheel cool according to its instructions. Heat from dry grinding can soften the steel at the edge, which shortens the life of the repair. A slow, cool grind protects the blade. 
| Tool | Strength | Watch out for | 
| Coarse sharpening stone | Steady control of the bevel angle | Needs flattening and water | 
| Coarse grinding wheel | Fast metal removal | Heat buildup on a thin edge | 
| Diamond plate | Cuts hard steel well | Leaves deep scratches if pressed hard |  

## Set and hold the bevel angle 

The bevel angle decides how the cleaver cuts and how long the edge holds. A shallower angle gives a keener edge, while a steeper angle puts more steel behind the edge. Match the angle to the existing cleaver bevel so the blade keeps its shape. 

Find the angle by laying the bevel flat on the stone and rocking the blade until the edge touches. Lock your wrists and move the whole blade in steady passes. Keeping the angle fixed is the main skill in regrinding cleaver bevel work. 

Grind in overlapping strokes that cover the full length of the edge. Vary the direction so the scratches cross and show where metal has been removed. Stop and look at the edge often to keep the bevel even from heel to tip. 

## Work through the chip in stages 

Grinding a chipped cleaver edge goes faster when you work in stages. Start with the coarse tool and grind the damaged section until the chip becomes a shallow dip. Then widen the grinding to blend that dip into the rest of the bevel. 

Keep the passes short and check the mark you made on the chip. When the mark is gone, the chip has been ground out and the edge is straight. Clean the stone or wheel as it loads with metal so it keeps cutting. 

Flip the blade and grind the other side to match. An even bevel on both faces keeps the edge centered in the blade. Check the edge from the end of the blade to confirm the two sides meet in a straight line. 

- Inspect and mark the chip before grinding.
- Grind the chip area with a coarse tool at the set angle.
- Blend the dip into the rest of the bevel.
- Match the second side to the first.
- Check the edge from the end for straightness.
 

## Raise a burr, then remove the burr 

A burr is a thin ridge of metal that forms on the opposite side as you grind. Burr removal is the step that tells you the two bevels have met along the full edge. Work each side until a burr runs from heel to tip, then switch sides. 

Use a finer stone to reduce the burr and refine the edge. Light, alternating passes on each side pull the burr back and forth until it breaks away. Keep the angle the same as during the coarse grinding so the edge stays consistent. 

Test the edge by slicing paper or cutting a soft vegetable with a controlled motion. A clean cut along the full length shows the burr is gone and the bevels meet. If the blade catches at one point, return to the stone for a few passes. 

## Safety and when to stop 

Regrinding a chipped cleaver edge involves a sharp blade and fast tools. Keep your fingers behind the edge and use a clamp or a firm grip on the blade. Wear eye protection when grinding, because metal dust and sparks fly. 

Stop grinding when the chip is gone and the edge is straight. More grinding only shortens the life of the blade and thins the steel behind the edge. If the chip is deep or the blade is cracked, a trained specialist should assess the repair. 

Clean and dry the blade after the work, then apply a thin coat of oil to the steel. Store the cleaver so the edge does not touch other tools. A protected edge stays straight until the next sharpening. 

## Questions about regrinding cleaver edges 

### Can a chipped cleaver edge be fixed at home? 

A chipped cleaver edge can often be fixed at home when the chip is shallow and the blade is sound. You need a coarse sharpening stone or grinding wheel, a steady hand and time to grind the full bevel. Deep chips, cracks or a bent blade call for a trained specialist. 

### What grit should I use to regrind a cleaver edge? 

A coarse grit is the right start for regrinding a cleaver edge, because it removes metal faster than a fine stone. The exact grit depends on the chip depth and the steel. Finish with a finer stone to refine the edge and remove the burr. 

### How do I know when the chip is gone? 

The chip is gone when the edge is straight along its full length and no dip remains. Mark the chip before grinding so you can watch it shrink, then inspect the edge from the side and the end of the blade. A straight line from heel to tip confirms the repair. 

### Should I grind both sides of the cleaver? 

Both sides of a double-bevel cleaver need grinding so the edge stays centered in the blade. Work one side until a burr forms on the other, then match the second side to the first. A single-bevel cleaver is ground on one face only, with the flat back kept flat. 

### Why does my cleaver still catch after regrinding? 

A cleaver that still catches after regrinding may have a remaining burr or an uneven bevel angle. Light alternating passes on a finer stone remove the burr and even out the edge. Check the edge from the end of the blade to spot any dip or high spot.
